ULTRA SENSITIVE HUMAN INSULIN RIA

I. INTENDED USE

Linco's Ultra Sensitive Human Insulin Radioimmunoassay (RIA) Kit provides approximately 10X greater sensitivity as compared to ordinary Insulin RIA techniques and is designed for use when Insulin concentrations are extremely low or when sample volumes are limited. It is a completely homologous assay since the antibody was raised against highly purified Human Insulin and both the standard and the tracer are prepared with Human Insulin. This kit is for research purposes only.

II. PRINCIPLES OF PROCEDURE

In radioimmunoassay, a fixed concentration of labeled tracer antigen is incubated with a constant dilution of antiserum such that the concentration of antigen binding sites on the antibody is limited, for example, only 50% of the total tracer concentration may be bound by antibody. If unlabeled antigen is added to this system, there is competition between labeled tracer and unlabeled antigen for the limited and constant number of binding sites on the antibody. Thus, the amount of tracer bound to antibody will decrease as the concentration of unlabeled antigen increases. This can be measured after separating antibody-bound from free tracer and counting one or the other, or both fractions. A standard curve is set up with increasing concentrations of standard unlabeled antigen and from this curve the amount of antigen in unknown samples can be calculated. Thus, the four basic necessities for a radioimmunoassay system are: a specific antiserum to the antigen to be measured, the availability of a radioactive labeled form of the antigen, a method whereby antibody-bound tracer can be separated from the unbound tracer, and finally, an instrument to count radioactivity.

 

The Linco Research Ultra Sensitive Human Insulin assay utilizes 125I-labeled Insulin and a Sensitive Human Insulin antiserum to determine the level of insulin in serum, plasma or tissue culture media by the double antibody/PEG technique.

III. REAGENTS SUPPLIED

Each kit is sufficient to run 250 tubes and contains the following reagents.

A. Assay Buffer

0.05M Phosphosaline pH 7.4 containing 0.025M EDTA, 0.08% Sodium Azide, and 1% RIA Grade BSA

Quantity: 40 ml/vial

Preparation: Ready to use

B. Human Insulin Antibody (Sensitive)

Guinea Pig anti-Sensitive Human Insulin Antibody in Assay Buffer

Quantity: 26 ml/vial

Preparation: Ready to use

C. 125I-Insulin (Sensitive)

125 I-Insulin Label, HPLC purified (specific activity 367 µCi/µg)

Lyophilized for stability. Freshly iodinated label contains <3 µCi (111 kBq), calibrated to the 1st Monday of each month.

Quantity: 27 ml/vial upon hydration

Preparation: Contents Lyophilized. Hydrate with entire contents of Label Hydrating Buffer. Allow to set at room temperature for 30 minutes, with occasional gentle mixing.

D. Label Hydrating Buffer

Assay Buffer containing Normal Guinea Pig Serum as a carrier. Used to hydrate Sensitive 125I-Insulin.

Quantity: 27 ml/vial

Preparation: Ready to use

E. Sensitive Human Insulin Standards

Purified Recombinant Human Insulin in Assay Buffer at the following concentrations:

0.2, 0.5, 1, 2, 5, 10, 20 mU/ml

Quantity: 2 ml/vial

Preparation: Ready to use

F. Quality Controls 1 & 2 (Sensitive)

Purified Recombinant Human Insulin in Assay Buffer

Quantity: 1 ml/vial

Preparation: Ready to use

G. Precipitating Reagent

Goat anti-Guinea Pig IgG Serum, 3% PEG and 0.05% Triton X-100 in 0.05M Phosphosaline, 0.025M EDTA,

0.08% Sodium Azide

Quantity: 260 ml/vial

Preparation: Ready to use; chill to 4°C.

IV. STORAGE AND STABILITY

 

Refrigerate all reagents between 2 and 8°C for short-term storage. For prolonged storage (>2 weeks), freeze at £ -20°C. Avoid multiple (>5) freeze/thaw cycles. Refer to date on bottle for expiration when stored at £ -20°C. Do not mix reagents from different kits unless they have the same lot number.

V. REAGENT PRECAUTIONS

A. Radioactive Materials

This radioactive material may be received, acquired, possessed and used only by research personnel or clinical laboratories for in vitro research tests not involving internal or external administration of the material, or the radiation therefrom, to human beings or animals. Its receipt, acquisition, possession, use and transfer are subject to the regulations of the U. S. Nuclear Regulatory Commission (NRC) or of a State with which the Commission has entered into an agreement for the exercise of regulatory authority.

The following are suggested general rules for the safe use of radioactive material. The customer's Radiation Safety Officer (RSO) is ultimately responsible for the safe handling and use of radioactive material.

1. Wear appropriate personal devices at all times while in areas where radioactive materials are used or stored.

2. Wear laboratory coats, disposable gloves, and other protective clothing at all times.

3. Monitor hands, shoes, and clothing and immediate area surrounding the work station for contamination after each procedure and before leaving the area.

4. Do not eat, drink, or smoke in any area where radioactive materials are stored or used.

5. Never pipette radioactive material by mouth.

6. Dispose of radioactive waste in accordance with NRC rules and regulations.

7. Avoid contaminating objects such as telephones, light switches, doorknobs, etc.

8. Use absorbent pads for containing and easily disposing of small amounts of contamination.

9. Wipe up all spills immediately and thoroughly and dispose of the contaminated materials as radioactive waste. Inform Radiation Safety Officer.

B. Sodium Azide

Sodium Azide has been added to all reagents as a preservative at a concentration of 0.08%. Although it is at a minimum concentration, Sodium Azide may react with lead and copper plumbing to form highly explosive metal azides. On disposal, flush with a large volume of water to prevent azide build up.

 

VI. MATERIALS REQUIRED BUT NOT PROVIDED

1. Borosilicate glass tubes, 12 x 75 mm. (NOTE: Polypropylene or polystyrene tubes may be used if the investigator finds that the pellet formation is acceptably stable in their system.)

2. 100 µl pipet with disposable tips

3. 100 µl & 1.0 ml repeating dispenser

4. Refrigerated swing bucket centrifuge capable of developing 2,000 - 3,000 xg. (Use of fixed-angle buckets are not recommended.)

5. Absorbent paper

6. Vortex mixer

7. Refrigerator

8. Gamma Counter

VII. SPECIMEN COLLECTION AND STORAGE

1. A maximum of 100 µl per assay tube of serum or plasma can be used, although, 50 µl per assay tube is adequate for most applications. Tissue culture and other media may also be used.

2. Care must be taken when using heparin as an anticoagulant, since an excess will provide falsely high values. Use no more than 10 IU heparin per ml of blood collected.

3. Specimens can be stored at 4°C if they will be tested within 24 hours of collection. For longer storage, specimens should be stored at £ -20°C. Avoid multiple (>5) freeze/thaw cycles.

4. Avoid using samples with gross hemolysis or lipemia.

VIII. ASSAY PROCEDURE

For optimal results, accurate pipetting and adherence to the protocol are recommended.

Day One

 

1. Pipette 300 µl of Assay Buffer to the Non-Specific Binding (NSB) tubes (3-4). Pipette 200 µl of Assay Buffer in the Reference (Bo) tubes (5-6). Pipette 100 µl of Assay Buffer to tubes seven through the end of the assay.

2. Pipette 100 µl of Standards and Quality Controls in duplicate (see assay flow chart).

3. Pipette 100 µl of each sample in duplicate. (NOTE: Smaller volumes of sample may be used when Insulin concentrations are anticipated to be elevated or when sample size is limited. Additional Assay Buffer should be added to compensate for the difference so that the volume is equivalent to 100 µl (e.g., when using 50 µl of sample, add 50 µl of Assay Buffer). Refer to Section IX for calculation modification.

4. Pipette 100 µl of Sensitive Human Insulin antibody to all tubes except Total Count tubes (1-2) and NSB tubes (3-4).

5. Vortex, cover, and incubate overnight (20-24 hours) at room temperature.

Day Two

6. Hydrate the Sensitive 125I-Insulin tracer with 27 ml of Label Hydrating Buffer. Gently mix. Pipette 100 µl of Sensitive125I-Insulin to all tubes. Freeze any unused tracer for future use.

7. Vortex, cover and incubate overnight (22-24 hours) at room temperature.

Day Three

8. Add 1.0 ml of cold (4°C) Precipitating Reagent to all tubes except Total Count tubes (1-2).

9. Vortex and incubate 20 minutes at 4°C.

10. Centrifuge, at 4°C, for 20 minutes at 2,000-3,000 xg. Note: If less than 2,000 xg is used, the time of

centrifugation must be increased to obtain a firm pellet (e.g. 40 minutes). Multiple centrifuge runs within an assay must be consistent. Conversion of rpm to xg:

xg = (1.12 x 10-5) (r) (rpm) 2

r = radial distance in cm (from axis of rotation to the bottom of the tube)

rpm = revolutions per minute

11. Immediately decant the supernate of all tubes except Total Count tubes (1-2), drain tubes for at least 15-60 seconds (be consistent between racks), and blot excess liquid from lip of tubes. NOTE: Invert tubes only one time. Pellets are fragile and slipping may occur.

12. Count all tubes in a gamma counter for 1 minute. Calculate the mU/ml of Human Insulin in unknown samples using automated data reduction procedures (see Section IX).